Perrycraft Aventura Truck Bed Rails Manuel d'utilisateur télécharger pdf

3) Install end supports to side rails using the #8 x 5/8

self-threading screws. Do not tighten screws

completely at this point.

Increase Rail Curvature-Rail Upside Down

Decrease Rail Curvature-Rail Right Side Up

Neoprene

Pad

Center

Post

#10x1

Oval-head

Waxed

Screw

Side

Rail

Support

Base

(A-L or A-R)

Side Rail

#8x5/8" Screw

INAV-RRL (Page 1 of 2) 120918

Roof Rails and Truck Bed Rails

Installation Instructions

CAUTION: Do not use the mounting hardware contained in this unit to install rails on Fiberglass or Composite

Plastic surfaces. Supplemental hardware pack, part# HWAVTC-UV, is required for installing rails on such non-

metal surfaces. Please contact the Distributor from whom the unit was purchased or contact the Perrycraft

Customer Service Dept at 800-777-7081 to obtain the necessary supplemental hardware pack if installing these

roof rails on a Fiberglass or Composite Plastic surface.

CONTENTS: 2 - side rails, 2 - Left end supports and mating covers; 2 - Right end supports and mating covers;

Center Support Posts: 2-posts in 68" & 78" Roof Rails, 4-posts in 88" Roof Rails and all Bed Rails;

1  hardware pack (Containing 4-#8x5/8 self-threading screws; 12-#10x3/4 waxed-tip pan head

screws; 4-1/4 Stainless Steel Flat Washers; #10x1 Waxed-tip Oval-head Screws: 2-screws in

68" & 78" Roof Rails, 4-screws in 88" Roof Rails and all Bed Rails; and 1-instruction sheet).

Tools required: Phillips screwdriver; electric drill; 1/8 drill bit; center punch; pencil or marker.

For Truck Bed Rail installation, skip to Step 2.

1) As universal Roof Rails are designed to fit several different vehicles, the bow / curvature of the side rails

may not exactly match the roof contour of a particular vehicle. NOTE: The rails should be dry fit to the

roof panel before installing. Carefully place one of the rails (without end supports or center support posts)

on the vehicle roof in the approximate location to be installed. The curvature of the rail should approximate

the roof contour. If rail is under-curved and there is more than a 3/16 space between the ends of the rail

and the vehicle roof panel, or over-curved and there is more than a 3/16 space between the center of the

rail and the roof panel, bench adjusting the curvature of the rails is required. Adjust by suspending the rail

between two points (4x4 wooden blocks, two tables, etc). To increase the curvature, start with the rail upside

down; to decrease the curvature, start with the rail right side up (see appropriate illustration below). With

hands spaced shoulder-width apart, apply sufficient pressure to the rail to increase or decrease the curvature

as desired. Repeat this process for both rails.

Important Note: While made of extruded aluminum, the rails are heat-treated for added strength.

Therefore, several applications of adequate springing pressure may be required to modify the curvature

of the rails.

2) Slide center posts into groove on bottom

of rails (applicable only on rails of 68 or

longer).

(over)

1 2

Résumé du contenu

Page 1 - Installation Instructions

3) Install end supports to side rails using the #8 x 5/8 self-threading screws. Do not tighten screws completely at this point.Increase Rail Cur

Page 2 - Flat Washer

#10x3/4Waxed Screws#8 x 5/8 ScrewNylonWasherSupport Base(A-R or A-L)Side RailNeoprene PadSlide vertical blade of cover into gap between base and wal

Commentaires sur ces manuels

Pas de commentaire

Perrycraft Aventura Truck Bed Rails Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Perrycraft Aventura Truck Bed Rails. Perrycraft Aventura Truck Bed Rails User Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Perrycraft Aventura Truck Bed Rails